Specifications
Model Specifications
The Grate Range provides a selection of fireplace inserts that incorporate the EcoSmartTM Burner in a simple, traditional manner. A great way of rekindling a closed off open fire, or perhaps creating a unique fireplace feature - without the fuss. All models include Burner Kit.
Applicable EcoSmartTM Burner
BURNER ONE – please refer to applicable Model Specification.
Fuel
Use Denatured Ethanol only.
Design Features
The Modern Grate is a low line rectangular shaped grate made of steel (rust treated) featuring four legs that suspend the burner shelf off the ground and a modern surround that features simple lines. The grate includes a built in EcoSmartTM Burner in black steel (rust treated).
The grate includes a built in EcoSmartTM Burner.
Construction Detail
GRATE: The Modern Grate is made of black steel and specifically designed to accept the EcoSmartTM Burner.
BURNER: Placement and clearance allocated for one (1) EcoSmartTM Burner only.
TRAY: The Modern Grate has an inbuilt top tray to increase safety (e.g heat transfer & accidental spillage collection).
SPACERS: The Modern Grate features inbuilt spacers on the top, sides and rear of the burner so that construction material cannot be applied directly onto the surface of the actual burner.
Ventilation
EcoSmartTM Fires do not require any form of permanent fixture or fitting, such as a flue for ventilation, a permanent gas connection or any kind of fixed utility for fuel supply.
Denatured Ethanol is certified safe to burn indoors without venting, because its main by-products are carbon dioxide, water steam and heat.
In a house of typical construction, that is, one that is not of unusually tight construction due to heavy insulation and tight seals against air infiltration, an adequate supply of air for combustion and ventilation is provided through infiltration. However, if the fireplace is used in a small room where less than 5.7m3 [200ft3] of air space is provided for each 1000 BTU per hour of fireplace rating (considering the maximum burner adjustment),
the door(s) to adjacent room(s) should be kept open or a window to the outside should be opened at least 25.4mm [1in] to guard against potential build up of indoor air pollution. Do not install or operate in a bathroom or any other small room.
The room cannot be less than 70m3 [2472ft3] per burner.
Recommended Accessories
Fire Extinguisher, EcoSmartTM Fire Screen or alternative Wind Screen.
Compulsory Cross Reference
Please ensure you read the applicable Model Specifications for the EcoSmartTM Burner that is used in this model before ordering, specifying, installing or operating the EcoSmartTM Burner.
Clearances
CONVERSION OF AN EXISTING FIREPLACE/INSERTING INTO A FIREBOX SETTING: The grate can only be fitted into a fireplace opening that is W 650mm [25.6in] x H 800mm [31.49in] x D 500mm [19.7in].
The fireplace surround and base must be made out of a non-combustible material such as stainless steel, brick, concrete etc.
In order to keep the heat from escaping through the flue, place a panel of non-combustible heat reflective material such as stainless steel across your flue opening.
INSERTING WITHOUT A FIREBOX SETTING: REAR: A minimum 30mm [1.2in] space between the grate and the rear wall. If the rear wall is combustible, a distance of 600mm [23.62in] must be allowed for. FRONT: A minimum of 45mm [1.75in] space between the grate edge and the front edge. OVERHEAD: A minimum clearance of 1650mm [64.96in]. SIDES: A minimum clearance of 600mm [25.6in] from the grate (if combustible material). BASE: Must be made of non-combustible material.
Installation Requirements
Models from the Grate Range must not be operated before being installed in a fixed secure position using the screws supplied.
The floor must be level and the grate positioned on a flat surface.
The floor must be made out of a non combustible base.
To prevent accidental tipping, the EcoSmartTM Fire must be installed into a fixed secure position using the parts supplied, following these instructions.
Equipment required: pencil, long handled phillips head screw driver, hammer and drill. 1. Confirm that you have received all necessary fixings as illustrated; 2. Position the Grate in accordance to the compulsory minimum clearances outlined in the Instruction Manual. 3. Using a pencil, mark the screw position on the two (2) brackets at the base of the Grate; 4. Remove the Grate and drill holes in the centre of the positions marked; Hammer the supplied plastic plugs
into the holes. 5. Place the Grate back into position and secure into position using the supplied screw.
Do no over-tighten.
